C3 RS915 REV. A 1 C3-RS-915 PROFESSIONAL 2-WAY 915 MHz. LCD REMOTE CAR STARTER & 6 CHANNEL ALARM SYSTEM With Built-in Voltage & Temperature
C3 RS915 REV. A 10 H6: 22 PIN WIRE CONNECTORS: H6/1 BROWN/BLACK WIRE: 200 mA (-) Ground Output When Running. This wire provides a negative output du
C3 RS915 REV. A 11This output is for a Key Sense wire by -pass that some Chrysler and Toyota vehicles need to activate remote start. This wire comes o
C3 RS915 REV. A 12When the BLACK/WHITE wire is grounded, the remote start unit is operable. When this wire is open from ground, the remote start is di
C3 RS915 REV. A 13instance, this timer output may be used to turn on the headlight with the remote control. Also on certain BMW, Mercedes Benz, Jaguar
C3 RS915 REV. A 14 H6/14 Yellow wire – (-) 200mA Ignition 3 Output – This wire provides a 200mA (-) ground output that becomes active 4 seconds befor
C3 RS915 REV. A 15To + 12 VIgnitionSwitchYELLOW wireMatching ResistorVATS control Module87a86308785VAT wire (#1)VAT wire(#2) H6/15 Green wire – Neg
C3 RS915 REV. A 16The WHITE/BLACK wire provides an instant shutdown for the remote start, whenever it is grounded. Connect the wire to the hood pin sw
C3 RS915 REV. A 17Blue WireGreen Wire( - ) Lock Pulse( + ) Unlock Pulse( - ) Unlock Pulse(+) Lock PulseRed(not used) NEGATIVE TRIGGER DOOR LOCK SYSTEM
C3 RS915 REV. A 182 STEP DOOR UNLOCK WIRE CONNECTION FOR GROUND SWITCHED DOOR LOCKS Cut Existing Unlock X Lock Unlock OEM Door Master Lock Switch To A
C3 RS915 REV. A 19 Press Transmitter Button One Chirp / LED one pulse Factory Default Setting Two Chirps / LED two pulses Three Chirps / LED three pul
C3 RS915 REV. A 2 TABLE OF CONTENTS: INSTALLATION DIAGRAMS 4 H1: 6 PIN HEAVY GAUGE WIRING CONNECTION 6 H1/1 Violet Wire – Starter Output 6 H1/2
C3 RS915 REV. A 201 Turn the Ignition switch ‘ON/OFF’ 3 TIMES and stay in OFF position. 2 Push the Valet switch 5 times (holding in on the 5th pus
C3 RS915 REV. A 21(The system Can not be Arm with the engine running) The shock sensor will be by-passed upon engine running. (The engine will run b
C3 RS915 REV. A 222 H6/6 Brown / White Wire = (-) 200mA Horn Output H6/6 Brown / White Wire = Factory Security Rearm Signal Output 3 Fahrenheit
C3 RS915 REV. A 233. When the desired interval has passed, release the valet switch. 1 long chirp for confirmation. (Set to any interval between 1 s
C3 RS915 REV. A 242. Push the Valet switch 7 times (holding in on the 7th push) it until three chirps with one long chirp is heard then release the va
C3 RS915 REV. A 255 Door lock before start Door lock after shut-down Door lock before start and Door lock after shut-down Without this feature 6
C3 RS915 REV. A 265 Start or Stop the system for TESTING & ADJUSTMENT 6 + “TEST” Mode for Zone 2 / instant trigger & Zone 3 / Door tri
C3 RS915 REV. A 276. Press and hold the valet switch for 2 seconds until a long chirp and the LED light constant for two seconds. The RPM signal is le
C3 RS915 REV. A 28b. Press button on the transmitter to set proper “Start Timer”. The chirp & LED pause will confirm entry. (Decrease “Start T
C3 RS915 REV. A 29Press and release the transmitter and buttons at the same time once. [1] LED flash, [1] siren/horn chirp to indicate your are
C3 RS915 REV. A 3Test the Hood Pin shutdown circuit 31 Neutral Start Safety Test 31 Mechanical Neutral Safety Switch Considerations 31 Park/Neutral
C3 RS915 REV. A 30TROUBLE SHOOTING There are 5 reasons why the remote start button will not respond from the transmitter. 1. The Black/White Neutr
C3 RS915 REV. A 31Failure to test the unit in the following manner may result in personal injury, property damage, or both. 1. Test the BRAKE shutdown
C3 RS915 REV. A 32installing the Remote Start Unit in. 2. Connect the BLACK/WHITE Neutral Safety Switch wire (H6/8) to this reference wire. NOTE: If
C3 RS915 REV. A 33A. Locate the control wire that connects the driver’s door pin switch to the key in sensor switch. B. Cut this wire and connect th
C3 RS915 REV. A 34 Available At an Authorized Autopage Dealer The RS-900 is CI3 Compatible It is recommended to have a minimal digital service plan
C3 RS915 REV. A 35 BLANK PAGE
C3 RS915 REV. A 36 960 Knox Street Unit B Torrance, California 90502 Main Office: 310-323-1800 Technical Support: 800-945-252
C3 RS915 REV. A 37www.autopageusa.com 2-Way Communication to the Power of 3
C3 RS915 REV. A 4 INSTALLATION DIAGRAM
C3 RS915 REV. A 520A20ARed: Remote Start Power 1Red: Remote Start Power 2Violet: Starter (+) OutputPink: Ignition 2 (+) OutputYellow: Ignition 1 (+) O
C3 RS915 REV. A 6 WIRING Keep wiring away from moving engine parts, exhaust pipes and high-tension cable. Be sure to tape wires that pass through
C3 RS915 REV. A 7 Red Wire (2) — +12V Power Input Remove the two 20A fuses prior to connecting these wires and do not replace them until the satellite
C3 RS915 REV. A 8serial data modules and is not included with the RS-900. This two-way data port has been designed for use with all C I 3 compatible
C3 RS915 REV. A 9H7. 4-PIN BLACK CONNECTOR. – TWO-WAY TRANSCEIVER/ANTENNA MODULE The Two-way transceiver/antenna mounting location should be the upper
Comments to this Manuals