Autopage MA-200 Installation Manual

1 C3-RS-625 PROFESSIONAL TWO WAY REMOTE CAR STARTER & KEYLESS ENTRY SYSTEM With Two Way Serial Port Data Link INSTALLATION MANUAL Compa

10 H3. 4-PIN BLACK CONNECTOR. – TWO-WAY TRANSCEIVER/ANTENNA MODULE The Two-way transceiver/antenna mounting location should be the upper lef

11YELLOW WIRE: (-) 200ma IGNITION 3 OUTPUT – This wire provides a 200mA (-) ground output that becomes active 4 seconds before the remote start un

12 WHITE WIRE – (-) 200ma PROGRAMMING OUTPUT (See Alarm Feature A - 2 Programming) DOME LIGHT CONTROL OUTPUT (Factory Default Setting)— This w

13FACTORY SECURITY DISARM SIGNAL OUTPUT – (See Alarm Feature A - 3 Programming) This wire is designed to disarm a factory installed security syste

14BLACK/WHITE WIRE — (-) Remote Start Enable Toggle Switch Input (-)Neutral Safety Switch Input — When the BLACK/WHITE wire is grounded, the rem

15Important! This connection is a safety wire and must be connected as shown and tested as specified. Failure to do so may result in personal in

16 BLUE/BLACK WIRE : 200 mA (-) Second Accessory Output This wire will provide a negative output that can be used as a second accessory wire if ne

17 +12V Master Door Lock Switch X X Splice Splice Cut the Existing Lock Wire To Door Lock Motor To Slave Door Lock switches Cut the Existing Unloc

18 2 STEP DOOR UNLOCK WIRE POSITIVE SWITCHED DOOR Cut Existing Unlock Wire X Lock Unlock OEM Door Master Lock Switch To All Other

19its commands directly from the CPU of the RS-622. This will provide greater theft protection as well as aid in the installation of this product

2HJKL TABLE OF CONTENTS: Introduction 3 Installation Diagram 4 Wiring Diagram 5 Wiring Diagram H/7 14-pin Connector 6 Wiring Description H/

20 flash, [3] horn chirps etc. Press Transmitter Button One Chirp / LED one pulse Factory Default Setting Two Chirps / LED two pulse Three

21Press Transmitter Button One Chirp / LED one pulseFactory Default Setting Two Chirps / LED two pulse Three Chirps /LED three pulse Four Chirps /

22NOTE: Before an attempt to remote start, the unit must be programmed for a system type, Tachometer Check, Voltage Check or Timer Check. If non

236 + Vehicle without Turbo (The system Can not Arm with the engine running) Vehicle with Turbo (The system Can be Armed with the engine ru

246 + + 50 RPM DBI ONLY No RPM learning 7 + - 50 RPM DBI ONLY No RPM Learning or < 50RPM Exit: Press the button on the transmi

25 RPM LEARNING: While the system is in Start Feature “D” programming mode, 1. Press and release the transmitter button once, [1] LED flash

26now in the Start feature ‘D’ programming mode. Select “Checking Type”: 3. Press the transmitter + button to set the “Voltage Checking Type”.

27chirps with a long chirp is heard then release the valet switch. You are now in the Start feature ‘D’ programming mode. Select “Checking Type”:

284. Press the button first within 3 seconds, then press the + button on the transmitter together for 6 seconds, there will be a confirmati

296 System timed out 7 Transmitter 8 Tach. Signal has not been learned Re-learning the RPM (Start Feature D – 2 / 3) TESTING YOUR INS

3 INTRODUCTION This Remote Starter with Alarm and Keyless Entry System has been designed to be installed on fuel-injected vehicles with an au

30MECHANICAL NEUTRAL SAFETY SWITCH CONSIDERATIONS: Mechanical neutral safety switch configurations differ slightly in that they do not offer the s

31KEY IN SENSOR CIRCUITS: If the vehicle you are working on does not have or you cannot locate the ECM reference wire, there are two alternatives

32D. Cut this wire and connect the ignition cylinder side to terminal 30 of a P&B VF45F11 or equivalent relay. E. Connect the cathode (strip

33 Available At an Authorized Autopage Dealer The RS-625 is CI3 Compatible

34It is recommended to have a minimal digital service plan on your cell phone. 960 Knox Street Unit B Torrance, California 90502

352-Way Communication to the Power of 3

4 INSTALLATION DIAGRAM: C3-RS-625H1 6 Pin Wht.H2 5 PinH7 14 Pin WhiteH4 ValetH3ANT.H6 DLH5LEDTRX-76ValetSwitchViolet : Starter OutputRe

5 WIRE DIAGRAM: #H1 6 PIN HEAVY GAUGE WIRE HARNESS 20A20ARed: Remote Start Power 1Red: Remote Start Power 2Violet: Starter (+) OutputPink:

6 #H7. 14 PIN MOLEX CONNECTOR: WIRING Keep wiring away from moving engine parts, exhaust pipes and high-tension cable. Be sure to tape wir

7Failure to make this connection properly can result in personal injury and property damage. In all installations it is the responsibility of th

8 PINK Wire – Ignition 2 Output Some vehicles have [2] ignition wires that must be power. Connect the PINK wire to the ignition 2 wire from the

9 BLACK WIRE — SYSTEM GROUND – This is the main ground connection of the alarm module. Make this connection to a solid section of the vehicle fr